Omron ZW-7000 Series User Manual Download Page 179

Page: 179 / 336

Setting I/O

ZW-8000/7000/5000
User's Manual

177

Settin

gs for Function

Setting the non-measurement conditions

The measurement value can be set to the clamp value when there is an unexpected number of edges or

reflection power due to the state of the light reception waveform.

At this time, "------" is displayed on the controller's main display.

* With ZW-7000

/5000

, this setting is not possible.



Multi View Explore

: [Bank Group] | [(Bank Data Name)] (double click)

→

Edit pane

: [I/O Settings] icon (

)

→

I/O Setting Screen

: [Non-Measuring Specification]

Setting item

Setting value

Description

Reflection power ON/OFF

When set to ON, the measurement value
is set to the clamp value when less than
the set reflection power threshold.

Reflective power
threshold

1 to 1000

Set the reflection power threshold value.
Reflection power is the strength of light
returning from the workpiece.

Number of Edge ON/OFF

When set to ON, if the set edge number
condition is not met, the measurement
value is set to the clamp value.

Condition for
number of Edge

surface/ 2 surface /3 surface /4 surface /Edge 5 or more

Set the edge number condition.

Comparison
condition of
number of Edge

(Condition for number of Edge) = (Observed number of Edge)/

(Condition for number of Edge)

≤

(Observed number of Edge)/

(Condition for number of Edge)

≥

(Observed number of Edge)

Set the edge number comparison
condition.

Set the operating mode to the FUNC mode.

3-2 Switching operation modes p.98

Set the condition of the non-measurement

value at [Non-Measuring Specification].

Set [Reflective power threshold], [Condition for number of Edge] and [Comparison condition of

number of Edge].

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands