manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 209

Offline Debugging of the Sensor Control Program and Sensor Operation

ZW-8000/7000/5000 
User's Manual

207

 6

 

Offl

ine Settings

2

Select the ZW that was added to the Edit Network Configuration Tab Page and change the node 

address of the ZW to the node address that is set on the ZW hardware switches.

Setting Up the ZW

Set up the inspections in the ZW, e.g., set the inspection items.

Executing the Simulation

1

Double-click the ZW that was added to the 

Edit Network Configuration Tab Page.

The ZW Setup Pane is displayed for the Edit 

Pane. Make all of the required settings.

1

Write and build the user program that will 

operate the machine.

Refer to the 

Sysmac St

u

dio Version 1 Operation 

Man

u

al 

(Cat. No. W504) for details on 

programming.

2

Open the Edit screen.

Right-click [(Sensor model)] in the Edit network 

configuration Tab page and select [Edit].

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands