manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 88

Launching a project

86

ZW-8000/7000/5000 

User's Manual

2-6 Launching a project

Connecting to the sensor with Sysmac Studio Measurement Sensor Edition

Creating a new project

Create a new project, add a sensor to the project, then start communicating with the sensor.

 3 Operation during RUN Mode p.95

1

Start up the PC tool.

2

Create a new project.

Click [New Project] and select [Displacement 

Sensor] from [Category] under [Select Device], 

and [ZW] from [Device].

 

Then enter [Project name], [Author], and 

[Comment].

 

Click [Create] to create a blank project.

3

Specify the sensor to connect using one of 

the methods below.

• Directly specify the IP address of the sensor to 

connect.

 

Check the [Specify a sensor] box. 

 

Directly enter the IP address. Click [Confirm], 
and then click [OK].

• When not connected with the sensor (offline)

 

When setting a project offline without 
connecting to the actual sensor, check [Enter 
the type] to select.

 

Then, select the sensor model and software 
version to use and click [OK].

 Chapter 

6 Offline Settings p.201

By default, the Sensor Controller has an IP address of 192.168.250.50

If there are existing projects, click [Open Project].
A list of the projects is displayed. Select the proj-
ect you want to open and click [Open].
If an existing project is opened, it starts up in 
offline mode. For the details of offline mode, see 
below.

 

Chapter 6 Offline Settings p.201

Note

Note

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands