manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 197

Recovering Calibration ROM data

ZW-8000/7000/5000 
User's Manual

195

 5 

Co
nveni

ent Fun

c

tio
n

s

5-3 Recovering Calibration ROM data

If an abnormality occurs in the sensor's Calibration ROM, you can recover the backed up Calibration ROM data 

into the sensor.

 Multi view Explore

: [Device Group] | [(Sensor Name)] (double click)

 

→

 Edit pane

: [Tool] icon (

)

• The Calibration ROM data is different for each sensor serial number. Select the backup file that matches the sensor 

serial number. Measurement will not be correct unless they match.

• As a temporary measure if the Calibration ROM is lost, or fails, the measurement can be restarted using the last 

loaded Calibration ROM data according to the following procedure.

 <Operating procedures>

• Hold the button while [NO.ROM] is displayed on the sub digital. Press the ZERO/SET key after [OK/CAN] is 

displayed.

<Note>

• Confirm that the serial number of the Calibration ROM which is loaded is the same as the serial number of the 

Sensor Head by checking the Controller Information.

• If the serial numbers are not the same, measurement cannot be performed correctly.

• When restarting the Sensor Controller, perform the same procedures again.

• For a Displacement Sensor which has never been inserted or launched, this operation is disabled.

1

Set the operating mode to the FUNC mode.

 3-2 Switching operation modes p.98

2

Click the [ROM recovery] in [Sensor setup].

Select the Calibration ROM backup data file.

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands