manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 121

Bank switching

ZW-8000/7000/5000 
User's Manual

119

 3 

Opera

tio

n durin

g RUN Mo

de

3-9 Bank switching

Switching Banks

Switches banks.

You can also switch the bank by entering the non-procedural command.

 “5-1 Connecting by No-protocol Communications” described in Displacement Sensor ZW-8000/7000/

5000 series Confocal Fiber Type Displacement Sensor User’s Manual for Communications Settings 
(Z363)

1

Double click to open the bank group in the 

Multi View Explore.

2

Select the bank data to switch and double 

click or right click it to select the Edit menu.

The bank in the Bank data edit pane that is 

active on the Edit pane becomes the current 

bank.

Switching Banks can also be set by the operating keys on the Sensor Controller.

 

Switching Banks p.260

Important

Note

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands