manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 157

Setting the Output Conditions

ZW-8000/7000/5000 
User's Manual

155

 4 

Settin

gs for Function

Setting the Frequency Filter

Set a filter to detect the changes in a specific frequency in the measured data.

(1) List of lowpass filter cutoff frequencies [Hz]

Item

Setting item

Setting value

Description

Frequency filter

Frequency filter

OFF (default value)

Frequency filter is not used.

Lowpass filter: 

0.040 to 23735.000

(default value: 0.040)

Detects only frequency components lower than the 
cut-off frequency. 
This can remove sudden fluctuations in 
measurement values and leave only gradual 
fluctuations.

Highpass filter: 

3.000 to 23725.000

(default value: 23725.000)

Detects only frequency components higher than the 
cut-off frequency. 
This can remove gradual fluctuations in 
measurement values and leave only sudden 
fluctuations.

Bandpass filter

Detects the frequency components between the cut-
off frequency (lower limit) and the cut-off frequency 
(upper limit).

Cutoff frequency

Refer to the table below.

Set this item when a low pass filter or a high pass 
filter is selected.

Cutoff frequency 
(Upper limit)

Set this item when a band pass filter is selected.

Cutoff frequency 
(Lower limit)

Sensor Controller 
type

Extension fiber 
cable length

Lower limit value

 

(1 area mode)

Lower limit value
(2 area mode)

Upper limit value

 

(1 area mode)

Upper limit value

 

(2 area mode)

Initial Value

ZW-8000

@

none

1

1

7909

3164

1

2 m

1

1

7909

3164

1

5 m

1

1

7909

3164

1

10 m

1

1

7909

3164

1

20 m

1

1

7909

3164

1

30 m

1

1

7909

3164

1

ZW-7000

@

none

1

1

23725

11862

2

2 m

1

1

23725

11862

2

5 m

1

1

23725

11862

2

10 m

2

2

23725

11862

4

20 m

3

3

23725

11862

5

30 m

4

4

23725

11862

7

ZW-5000

@

none

1

1

5931

5931

1

2 m

1

1

5931

5931

1

5 m

1

1

5931

5931

1

10 m

1

1

5931

5931

1

20 m

1

1

5931

5931

2

30 m

1

1

5931

5931

2

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands