manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 251

Setting the Output Conditions

ZW-8000/7000/5000 
User's Manual

249

 7

 

Senso

r con

trol
ler 
ope

ra

ti

ons

Multi-point scaling (ZW-8000

@

 only)

Multi-point scaling p.148

Operating procedure

Steps

Key operation

Display

Description

1 to 5

For moving to “SCALE”, see steps 1 to 5 in p.246. 

6

Select “AUTO” as the scaling type. 
The current setting value is displayed on the sub-display.

Press 

/

 key to enter editing mode and the sub-display blinks.

Select “AUTO” and press the 

 key. 

7

Press the 

/

 keys to select “NPT” and press the  

  key.

8

Press the 

 key when the main display shows “POINT1”. 

9

Set the measured value of point 1. 
The current measured value is displayed on the main display and the 
current setting value is displayed on the sub-display. 

To edit numerical values, use the 

/

/

/

 keys.

Enter the setting value and then press the 

 key.

10

Press the 

 key when the main display shows “POINT2”. 

11

Set the measured value of point 2. 

To edit numerical values, use the 

/

/

/

 keys.

Enter the setting value and then press the 

 key.

12

“OK/CAN” is displayed on the sub-display. 
When continuing to set the next point measurement value, press the 

 key. 

When ending all point measurement value settings, press the 

 key. 

Repeat steps 10 to 12 until reaching a maximum of point 10. 

13

When pressing the 

key in step 12 or point 10 setting 

completes, "OK/CAN" is displayed on the sub-display.
When continuing to set the next point measurement value, press the 

 key. When ending all point settings, press the 

 key.

14

Press and hold the 

 key for two seconds or more to enter the 

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys" 
(p.222).

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands