manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 172

Setting the Output Conditions

170

ZW-8000/7000/5000 

User's Manual

Setting the Offset

Set this item to set the reference value by a zero reset to a value other than zero.

 Multi View Explore

: [Bank Group] | [(Bank Data Name)] (double click)

 

→

 Edit pane

: [Task Settings] icon (

)

 

→

 Task Settings window : [Zero reset]

Item

Setting item

Setting value

Description

Zero reset

Offset

-999.999999 to 999.999999 [mm]
(default value: 0)

Set the offset value.

1

Set [Status] to ON.

 

Setting the Status p.169

Offset can be set only when [Status] is set to ON.

2

Enter an offset value at [Zero reset] - [Offset].

The offset can also be set by the operating keys on the Sensor Controller.

Setting the Offset p.257

Important

Note

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands