manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 140

Setting Measurement Items

138

ZW-8000/7000/5000 

User's Manual

4-2 Setting Measurement Items

What is a Measurement Item?

Obtain the waveform data based on the specified sensing condition, and calculate the height/thickness of up to 

four surfaces included in the measuring range. Perform calculations using the output result of each task.

Count the measurement surface closest to the Sensor Head first (default value).

Measuring the Height

The count direction for measurement surfaces can be changed.

 

Setting Start Direction of Count Measurement Surfaces p.128

Sensor head

Edge 1st
Edge 2nd
Edge 3rd
Edge 4th

Note

The setting for common height 
measurements as shown in the 
following diagram is registered 
for TASK1 in advance. In such 
a case, this setting is not required.

Set this item when measuring 
the height of an object below 
a transparent object as shown 
in the following diagram.

Edge 1st

Height

Edge 1st

Edge 2nd

Measurement 
range

Transparent 
object

Sensor head

Sensor head

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands