Omron ZW-7000 Series User Manual Download Page 10

Page: 10 / 336

ZW-8000/7000/5000

User's Manual

• Handling fiber cables

Use them in compliance with the following. This may result in damage to the fiber cable.

- Fiber cable bend radiuses must be at least 20 mm.

- Do not yank hard on a fiber cable.

- Do not step on a fiber cable or place anything heavy on it.

- Do not apply any twisting stress to the fiber cable.

- Do not forcefully insert, or bend, or twist in a manner that would cause stress on the fiber connector when

connecting it.

- Do not let bending cause stress at the root section of a fiber connector and connection.

3. Grounding

• Use a frame ground terminal of the specified size to be grounded. Do not connect a wire with an only twisted

end directly to a terminal block.

Terminal screw: M4

Crimp-type terminal

• Use D-type grounding (ground resistance of 100

or less). Make the ground point as close as possible and

make the ground wire used as short as possible.

• Never share a ground wire with other equipment or connect to building beams to prevent the occurrence of a

potential difference between grounds (between 0V).

• The power supply circuit of the Sensor Controller is not insulated from the internal circuits.

• When grounding the positive (+) terminal of the 24 VDC power supply, do not connect the Sensor Controller's

frame ground terminal or PLC's frame ground terminal to ground. [(1), (2)]

The PC housing may be internally connected to the SG (0 V), in which case current will flow through the path

shown below and may cause seizure.

• If there is no PC, or specifically there is no SG (0 V)/FG short-circuiting path, grounding the Sensor

Controller's frame ground terminal will not cause seizure. Wire the PLC after checking the specification of

your PLC.

• The dedicated RS-232C cable (ZW-XRS2/XPT2) has its cable shield isolated from the connector housing.

[(3)]

4. Regulations and Standards

• EN61326-1

• Electromagnetic environment : Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

• The following condition is applied to the immunity test of this product.

: There may be cases that current or voltage output fluctuate within ± 3%F.S. when a sensor is experienced

electromagnetic interference.

8.5mm
or less

24V

24 V DC

power

supply

Sensor Controller

24V

PC or PLC

SG: Signal Ground (0 V for 24 V DC power supply)
FG: Frame Ground

(1)

(2)

Power supply

circuit

(3)

RS-232C

connector housing

RS-232C

Ethernet

connector housing

Ethernet

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands