manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 51

Basic Operations for Displaying Measurement Results

ZW-8000/7000/5000 
User's Manual

49

 1

Ba
si

c con

figuratio

n

• The calibration data is stored inside the Sensor Controller. Therefore, if the sensor head is calibrated once, as long 

as the fiber connection state does not change (if it is not disconnected from or connected to the Sensor Controller or 

an extension added), this operation is not needed each time. After removing/inserting a fiber cable from/to the Sen-

sor Controller, or extending a fiber cable, be sure to calibrate the Sensor Head again.

• When Sensor Head calibration fails

When sensor head calibration is performed in an inappropriate environment or with an extension fiber cable set 
incorrectly, an error message is displayed. In such a case, refer to the p.48, recheck your environment, and try 
again. If an error results even if Sensor Head calibration is done under the correct conditions, it is possible that 
some contaminants may have adhered to the Sensor Head part, or the fiber connector of the Sensor Controller. 
Clean the fiber cable or fiber connector referring to p.70. After cleaning the fiber or fiber connector, be sure to 
calibrate the Sensor Head again.

3

Click [Execute sensor head calibration].

The sensor head calibration window appears.

4

With no object in the measuring range, or 

with the tip of the sensor head shielded from 

light by an object that has the characteris-

tics of diffusion reflection, click the [Execute 

sensor head calibration] button.

• Re-adjustment is obviously required when described 

the following, warning message appears on the 

Multi-view Explorer.

• When the Sensor head is not adjusted correctly.

• When the extender fiber cable is added.

• The maximum value of the measurement cycle will 

differ depending on the extension fiber cable setting. 

If sensor head calibration was successful and the 

measurement cycle does not exceed the maximum 

value, there will be no impact on measurement 

accuracy even if the extension fiber cable setting is 

incorrect.

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands