Omron ZW-7000 Series User Manual Download Page 50

Page: 50 / 336

Basic Operations for Displaying Measurement Results

ZW-8000/7000/5000

User's Manual

Calibrating Sensor Head

Calibrate the Sensor Head by obtaining the dark data in the no-incoming light status.

• When removing and inserting a fiber cable from/to the Sensor Controller (Including the initial connection).

• When extending a fiber cable.

• When “Dark” is shown in the main display even though a measurement object exists in the measurement

range.

The Sensor Head should be calibrated without any object within 20mm of the measurement range or with the

tip of the Sensor Head shielded from light with an object with diffuse reflection.

Correct calibration is not possible with a transparent object, semi-transparent object, or mirror.

Select the cable length of the extension fiber cable.

Set the operation mode to FUNC mode.

3-2 Switching operation modes p.98



Multi View Explore

: [Device Group] | [(Sensor Name)] | [System] |

[System Data] (double click)

→

Edit pane

: [Sensor Settings] icon (

)

or he

asu

ring r

nge

• Witho

ny o

ject

within the me

asu

ring r

nge

• With light

hielded

ll with the tip of the

or He

hielded

n o

ject with diff

e reflection,

met

l, p

per, or pl

tic.

or he

asu

ring r

nge

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands