Omron ZW-7000 Series User Manual Download Page 207

Page: 207 / 336

Changing between Online and Offline

ZW-8000/7000/5000
User's Manual

205

Offl

ine Settings

When connecting online for the first time

• When connecting to a Sensor Controller online for the first time, the Calibration ROM data backup window

appears.

If the Calibration ROM is lost, or it fails, the backed-up data can be recovered to the Sensor Controller.

Please keep the backed-up Calibration ROM data.

5-3 Recovering Calibration ROM data p.195.

• When the Sensor Controller is in Setup mode; FUNC mode, online connection is disabled. Should switch to the

RUN mode.

Note

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands