manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 199

Printing the contents of settings

ZW-8000/7000/5000 
User's Manual

197

 5 

Co
nveni

ent Fun

c

tio
n

s

• The set contents of parameters can be output in CSV file format.

• CSV file output is as follows.

 

Note

1

Click [File output] button.

2

Enter the file name to save it to the desired 

folder.

The parameters are opened and output to the 

file.

Item

Property Name

Target Data

Sensor information

General settings

Name

ZW-7

Sensor Controller model name

ZW7000

Version

1.2**

Head model name

0

Head serial No.

00-00-00-00-00-00

MAC address

Comment

Bank group

BANK 1(1)

Sensing

Operation mode

1 area

Area mode

Normal

Material

100 tones

Background removal level

5 pixels

Measurement area1

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands