Omron ZW-7000 Series User Manual Download Page 41

Page: 41 / 336

Basic Operations for Displaying Measurement Results

ZW-8000/7000/5000
User's Manual

Ba
si

c con

figuratio

• Be sure to use a Sensor Head and Calibration ROM with the same serial number.

• A pair with different serial numbers cannot operate normally.

• Make sure to initialize the Sensor Controller when connecting a different type Sensor Head from that which was

connected the previous time the Sensor Controller was launched.

For the initialization method, see below.

Initializing Settings p.187

Initializing Settings p.271

Remove the Fiber cable

For ZW-8000/7000 Series

If you have the bush section of Fiber cable, that part may be out of place. Make sure to have the fiber
connector section.

When you remove the fiber cable, make sure to have the black part of the connector which indi-

cated.

Have the fiber connector (black part) illustrated under figure, and then pull out the direction of the arrow.

ZW-

000

erie

ZW-7000

erie

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands