Lotus 2005 Elise Owner'S Handbook Manual Download Page 88

Page: 88 / 205

b330

FRONT SPIGOT BRACKET

Hard Top - Fitting

1. Open both doors, and preferably with the aid of an assistant,

lower the roof onto the car holding aside the loose tethered

ﬁxings to avoid their entrapment or their causing paint damage.

Position the rear edge of the roof ﬁrst before locating the front

edge against the windscreen header rail.

2. Locate a front spigot bracket into its latch plate lower slot

(lifting the roof slightly to allow this) and retain to the roof with

the Torx bolt. Use only the special Torx tool supplied in the

car tool kit (stowed in the battery cover pocket), and do not

fully tighten at this stage.

3. Repeat step (2) for the opposite front spigot bracket.

l O

oh_croft_InD.indd 86

20/05/2004 07:59:02

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands