Lotus 2005 Elise Page 80 Owner'S Handbook Manual Download

Page: 80 / 205

ohs93

REMOVING ACCESS PANEL

Front Service Access Panels

The front body has two removable access panels to allow

servicing of the brake/clutch ﬂuid reservoir and main fusebox.

To remove an access panel:

Use the hexagonal key supplied

in the car tool kit (in the battery cover rear pocket), to release

the single threaded fastener securing the outboard corner of

the panel, and withdraw the panel from the two locating holes

in the front body spine.

Guard against the lightweight panel being blown away and

damaged by a strong wind.

To reﬁt a panel:

Hook the extended lip on the front edge of the

panel beneath the rear edge of the louvre panel before engaging

the two locating pegs on the inboard side of the access panel

with the holes in the front body spine. Fit the single screw at

the outboard corner of the panel into the captive nut in the body,

taking care not to cross-thread or overtighten the screw. Re-stow

the hexagonal key in the tool kit.

WARNING:

Ensure the access panels are reﬁtted and properly se-

cured before driving.

l O

oh_croft_InD.indd 78

20/05/2004 07:59:00

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands