Lotus 2005 Elise Owner'S Handbook Manual Download Page 110

Page: 110 / 205

exchangers from both frost damage, and metal corrosion. The

Elise is factory ﬁlled with a 50% concentration of Havoline XLC

Extended Life Coolant, which contains Organic Acid Technology

(OAT) based corrosion inhibitors to provide long coolant change

intervals combined with freedom from environmentally damaging

phosphates, silicates and nitrites.

NOTICE: No other type of coolant should be mixed with this

OAT coolant.

Havoline XLC may be identiﬁed by its orange colouration, and

by a label around the header tank ﬁller neck. The 50% concen-

tration provides freezing protection down to -40°F (-40°C), and

is recommended to be maintained throughout the life of the car.

Stronger concentrations should not be used.

In an emergency, if an OAT coolant is not available, the

cooling system should be topped up using water only, but the

reduction in freezing protection should be recognised, and the

concentration corrected promptly. In areas where the tap water

is extremely hard (exceeding 250 parts per million), distilled,

de-ionised or ﬁltered rain water should be used for the water

content of the coolant mix.

The effective level of ethylene glycol (anti-freeze) in the sys-

tem may be measured by your dealer using a hydrometer, but in

order to ensure that the required level of corrosion protection is

maintained, the coolant should be renewed every 4 years.

For coolant capacity, refer to ‘Recommended Lubricants‘

and ‘Technical Data’.

NOTICE: Using an incorrect coolant mixture may result in ex-

pensive damage to your engine and/or other car parts caused by

overheating, freezing or corrosion effects. This damage would

not be covered by your new car warranty.

Coolant Drain/Reﬁll Procedure

The cooling system of the Lotus Elise has been carefully

optimised to allow the required cooling performance using the

minimum volume of coolant. This provides for high cooling sys-

tem efﬁciency, with quick engine warm up and interior heating.

When reﬁlling the cooling system, it is vital to ensure that

the correct bleeding procedure is followed, and that no air

pockets remain. This operation should be entrusted to your

Lotus dealer.

g & M

108

oh_croft_InD.indd 108

20/05/2004 07:59:07

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands