Lotus 2005 Elise Page 64 Owner'S Handbook Manual Download

Page: 64 / 205

Air Re-circulation

The air supply for the interior climate system is normally drawn

from both the car interior and from the fresh air intake duct ahead

of the engine cooling radiator. When the re-circulation button is

pressed, the fresh air intake port is closed down to provide 90%

re-circulation air supply to the cabin interior. The re-circulation

facility should be used when maximum refrigeration is desired.

The tell tale in the switch button will light up blue when the

circuit is active.

Heater Temperature

With the left hand rotary control turned fully counterclockwise,

no heating is provided. If cooled air is required, use this tem-

perature position in conjunction with air conditioning.

Turning the control progressively clockwise provides in-

creasing levels of heat until at the fully clockwise position,

maximum heat is supplied.

Fan Speed

The centre rotary switch provides three fan speeds to boost air

circulation. Turned fully counterclockwise, the fan is off; Turning

the switch progressively clockwise operates the blower fan at

increasing speed in three steps.

Note that the fan operates only with the ignition switched on.

, V

n & A

p99

Temperature

Fan Speed

Distribution

Air conditioning

Air re-circulation

oh_croft_InD.indd 62

20/05/2004 07:58:56

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands