Lotus 2005 Elise Page 9 Owner'S Handbook Manual Download

Page: 9 / 205

Safety Information

To help you make informed decisions about safety, important

safety information is provided in forms including:

• Safety labels on the car

• Safety messages in this handbook are shown as follows:

WARNING:

The hazard and instructions to avoid the hazard are

given. If you do not take these instructions you and/or

others can be KILLED OR SERIOUSLY INJURED.

Messages prefaced by ‘NOTICE’ are intended to help

you avoid damage to your car, other property or the

environment.

Important Safety Precautions

You’ll ﬁnd many safety recommendations throughout this sec-

tion, and throughout this manual. The recommendations on this

page are the ones we consider to be the most important.

Always Wear Your Seat Belt

A seat belt is your best protection in accidents (including colli-

sions). Airbags supplement seat belts, but airbags are designed

to inﬂate only in a moderate to severe frontal collision. So even

though your car is equipped with airbags, make sure you and

your passenger always wear your seat belts, and wear them

properly. (See page 18).

Your Car is Not Recommended for Child Passengers

Since all children are safest in the back seat of a car, and

your car does not have a back seat, we strongly recommend

that you do not carry a child passenger. Children should be

carried in the Elise only if they are large enough to be able to

use the standard seat belt (see page 26). You should never

carry an infant in a rear-facing child seat in this car because

the Elise has a passenger airbag which cannot be switched off

or disabled (see page 26).

Be Aware of Airbag Hazards

While airbags can save lives, they can cause serious or

fatal injuries to occupants who sit too close to them, or are not

ty I

oh_croft_InD.indd 7

20/05/2004 07:58:41

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands