Lotus 2005 Elise Owner'S Handbook Manual Download Page 29

Page: 29 / 205

Behaviour:

It is essential that the behaviour of any child trav-

elling in the car is such that they remain correctly seated and

belted, and it is the responsibility of the driver to ensure that

this occurs.

The following wording has been included to comply with

National Highway Trafﬁc Safety Authority requirements,

however;

WARNING:

Lotus strongly recommends that you do not ﬁt any type

of child seat into the Elise due to the risk of death or seri-

ous injury if the child is too close to the dashboard when

the airbag inﬂates.

Procedure for Proper Fitment of Forward-Facing Child

Seat

Automatic Locking Retractor:

The safety belt for the passen-

ger’s seat is equipped with an automatic locking retractor that

must be used for securing a forward-facing child restraint sys-

tem. When activated, this retractor allows you to securely fas-

ten the child restraint system.

Activating the Automatic Retractor:

1. Pull the passenger seat safety belt

completely

out. At this

point, the locking mechanism is activated.

2. Place the forward-facing child seat in the passenger seat,

using the safety belt to secure the child seat,

following the

instructions that come with the child seat.

3. Insert the safety tongue into the buckle and make sure that

it is properly latched.

4. Allow the safety belt to retract until it is tight on the child seat.

You may further tighten the belt by pulling on it to allow more of

it to retract. Check to make sure the child seat is secured, and

that the belt is snug and will not pull out.

Releasing the safety belt and child seat:

1. Unbuckle the safety belt.

2. Remove the child seat.

3. Make sure that the belt has

fully

retracted. At this point the

automatic locking feature is disengaged.

g & S

ty R

oh_croft_InD.indd 27

20/05/2004 07:58:46

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands