manualshive.com logo in svg

Lotus 2005 Elise, Owner'S Handbook Manual

The Lotus 2005 Elise Owner's Handbook Manual is a comprehensive guide that provides detailed instructions and essential information about the iconic sports car. This manual is available for download absolutely free from our website, allowing you to access it anytime, anywhere. Get your hands on this essential manual today at manualshive.com.

Share
Download
background image

are located at the inboard rear of the seat. To increase lumbar 

support, squeeze the bulb repeatedly until sufficient support is 

obtained. To decrease support, press the small black button at 

the base of the inflator bulb.

Seat Belts

Seat  belts  provide  important  safety  and  comfort  for  both 

driver and passenger and have proven to be the single most 

effective safety device in reducing the risk of death or injury in 

a crash. The seat belts should be worn at all times, no matter 

how short the journey. This is required by law in most states 

and in all Canadian provinces. As a reminder, the seat belt tell 

tale  in  the  instrument  cluster  will  flash  until  the  driver's  seat 

belt is fastened, accompanied for the first eight seconds by an 

audible chime.

Inertia Reel Seat Belts

The standard fitment inertia reel seat belts allow the wearer 

freedom of movement under normal driving conditions. The belt 

reel will lock automatically whenever the car is subjected to brak-

ing, acceleration, or cornering forces, or on impact in a collision. 

Reel locking will also occur on steep hills or slopes, or if the 

car is tilted. In the event of a severe frontal impact sufficient to 

trigger the airbag system, a pre-tensioning device incorporated 

into each seat belt assembly will operate to tighten the belt for 

increased occupant protection.

ohs44

SEAT BELT POSITIONING

S

e

a

ti

n

g & S

a

fe

ty R

e

s

tr

a

in

ts

18

oh_croft_InD.indd   18

20/05/2004   07:58:43

Summary of Contents for 2005 Elise














































































































































































































Reviews:

No comments

Related manuals for 2005 Elise

Accel 2020 Installation Instructions preview
2020
Brand: Accel Pages: 2
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
Uebler F42 Mounting And Operating Instructions preview
F42
Brand: Uebler Pages: 18
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Brand: AC Schnitzer Pages: 20
Toro 137-1019 Installation Instructions Manual preview
137-1019
Brand: Toro Pages: 24
Caltrend LY115 Installation Instructions preview
LY115
Brand: Caltrend Pages: 3
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Toyota 4Runner 1999 Owner'S Manual preview
4Runner 1999
Brand: Toyota Pages: 285
Green Valley 601951 Instructions Manual preview
601951
Brand: Green Valley Pages: 17
ULTIMATE SPEED 1188 1525 Instructions For Use And Safety Manuallines preview
1188 1525
Brand: ULTIMATE SPEED Pages: 26
Painless Performance VORTEC 60211 Installation Instructions Manual preview
VORTEC 60211
Brand: Painless Performance Pages: 16
EUFAB 11439 Assembly preview
11439
Brand: EUFAB Pages: 8
Hamron 012463 Operating Instructions Manual preview
012463
Brand: Hamron Pages: 6
Audiovox CDC-TO3 Installation Manual preview
CDC-TO3
Brand: Audiovox Pages: 2

Brands by name

Popular brands

Load more brands