Lotus 2005 Elise Page 69 Owner'S Handbook Manual Download

Page: 69 / 205

Footbrake

Ventilated disc brakes are ﬁtted to all four wheels of the

Elise. These are operated by separate front and rear hydraulic

circuits, supplied from a tandem master cylinder with vacuum

servo. Anti-lock control is provided by a microprocessor based

electro-hydraulic unit, integrated into the base braking system.

The braking system is designed to provide good pedal feed-

back, with efﬁcient disc cooling to inhibit brake fade. With a

new car, or new brake system components, maximum braking

efﬁciency will be achieved if, for the ﬁrst few hundred miles,

needless heavy braking is avoided. Allow the brake pads and

discs to ‘bed in’ fully before using the brakes to their full potential.

Pedal effort will reduce as the brakes are bedded in, and as they

are warmed from cold to normal working temperature. Note that

the hard grade pad material may give rise to a certain amount

of brake noise under some conditions; such noise is not harmful

and does not affect the life or efﬁciency of the brakes.

WARNING:

• After driving through a ford, or a ﬂooded road, some loss

of braking response may be experienced until the brakes

have dried out. As soon as it is safe to do so after such

an encounter, apply the brakes until normal operation

is restored. Failure to do so may result in an accident in

which you or others may be killed or seriously injured.

• The brake assistance servo uses vacuum supplied from

the engine intake plenum, such that assistance is avail-

able only when the engine is running. Never coast down-

hill with the engine stopped. If this situation accidently

arises, avoid repeated application of the brakes, or the

stored vacuum supply will be rapidly used up. Greater

pedal pressures will be required. This may adversely

affect performance of the brakes which may result in an

accident in which you or others may be killed or seriously

injured.

Anti-lock Brake System

The Anti-lock Brake System (ABS) is used to optimise brake

performance in extreme conditions and reduce the potential

for any wheel to lock up. Under most conditions, the maximum

braking force is provided by a wheel which is rotating at about

90% of road speed. Apart from the likelihood of increasing the

g C

oh_croft_InD.indd 67

20/05/2004 07:58:57

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands