Lotus 2005 Elise Page 15 Owner'S Handbook Manual Download

Page: 15 / 205

petrol (LRP), will cause irreversible contamination of the pre-

cious metal catalysts and of the exhaust gas sensor used by the

computer controlled engine management system.

It is important that the Maintenance Schedule (see separate

booklet) is followed at the speciﬁed time and distance intervals

(this is a requirement of the warranty), and that the car is kept in

proper operating condition. Failure to do so may result not only

in a loss of fuel economy and emission control, but may cause

damage to the catalytic converter.

WARNING:

• If the engine malfunctions in any way (e.g by a change in

sound) have the fault diagnosed and repaired promptly.

Continuing to drive the car with an engine misﬁre could

cause the catalytic converter to overheat, with possible

heat damage to other car components, and an engine bay

ﬁre. Operation of the ‘Malfunction Indicator Lamp’ (MIL)

is fully described later in this handbook on page 49.

• DO NOT park or drive the car in areas where combustible

material, such as dry grass or leaves, could come into

contact with the hot exhaust system. Under certain wind

and weather conditions a grass ﬁre could be initiated.

• DO NOT tamper with any electrical components with the

battery connected. You could receive an electric shock

from the spark plug coils or initiate a car ﬁre.

• DO NOT check or adjust any engine bay equipment with

the engine running. Failure to comply with this may result

in you or your clothing becoming trapped.

• DO NOT use the car if a fuel leak is suspected, as may

be indicated by a persistent smell of fuel. Have the fault

diagnosed and rectiﬁed without delay. A fuel leak may

result in a ﬁre or explosion.

• DO NOT touch or approach, any part of a hot exhaust

system. Failure to comply with this may result in you

receiving severe burns.

• DO NOT allow servicing or repairs to be carried out by

unskilled persons as this may adversely affect the han-

dling and safety features on your car. Lotus dealers have

trained staff who are best qualiﬁed to maintain your car

to the correct speciﬁcation.

ty I

oh_croft_InD.indd 13

20/05/2004 07:58:42

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands