manualshive.com logo in svg

Lotus 2005 Elise, Owner'S Handbook Manual

The Lotus 2005 Elise Owner's Handbook Manual is a comprehensive guide that provides detailed instructions and essential information about the iconic sports car. This manual is available for download absolutely free from our website, allowing you to access it anytime, anywhere. Get your hands on this essential manual today at manualshive.com.

Share
Download
background image

NOTICE: Using incorrect wheel/tire equipment can also cause 

problems with wheel bearing life, brake cooling, speedo and 

odometer calibration, headlamp aim, ground clearance and tire 

clearance to the body.

 WARNING:

Dirt or corrosion on a wheel or hub mounting flange or 

wheel bolts, can result in the wheel bolts coming loose. 

The wheel could come off and cause a crash in which you 

and others could be killed or seriously injured. Thoroughly 

clean these components or fit new Lotus approved replace-

ments before fitting a wheel.

Never use oil or grease on the wheel bolts or hub threads. 

If you do, the bolts could come loose and the wheel could 

come off, causing a crash in which you and others could 

be killed or seriously injured.

Using  incorrect  wheel  bolts,  or  the  wrong  tightening 

torque could cause the bolts to come loose and the wheel to 

come off, resulting in a crash in which you and others could 

be killed or seriously injured. Use only the correct Lotus 

approved wheel bolts tightened to 77 lbf.ft (105 Nm).

NOTICE: Improperly tightened wheel bolts, or dirt on the wheel 

to hub mounting face can cause brake pulsation and judder, 

and damage the brake discs. To avoid expensive brake repairs, 

ensure complete cleanliness on assembly and tighten the wheel 

bolts in a diagonal sequence to the correct torque.

For advice and information on lifting the Elise, refer to ‘Lifting 

Points’ on page 148

T

ir

e

s & W

h

e

e

ls

128

oh_croft_InD.indd   128

20/05/2004   07:59:12

Summary of Contents for 2005 Elise














































































































































































































Reviews:

No comments

Related manuals for 2005 Elise

Jeep Commander Overview Manual preview
Commander
Brand: Jeep Pages: 25
Jeep Commander Warranty Information Booklet preview
Commander
Brand: Jeep Pages: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Brand: Farenheit Pages: 8
JASTEC von-S2 Instruction Manual preview
von-S2
Brand: JASTEC Pages: 12
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Brand: Wallbox Pages: 7
Caraudio-Systems v.LOGiC Intelligent Solution V5-NTG46 Manual preview
v.LOGiC Intelligent Solution V5-NTG46
Brand: Caraudio-Systems Pages: 18
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Vauxhall Astra 2021 Owner'S Manual preview
Astra 2021
Brand: Vauxhall Pages: 259
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
Honda 08V31-TE0-100A Installation Instructions Manual preview
08V31-TE0-100A
Brand: Honda Pages: 10
Hella 2DA 008 136-031 Mounting Instructions preview
2DA 008 136-031
Brand: Hella Pages: 2
Arrista SG8-19 Installation Manual preview
SG8-19
Brand: Arrista Pages: 2
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Brand: Chrysler Pages: 454
Yakima LockNLoad LightenUp Manual preview
LockNLoad LightenUp
Brand: Yakima Pages: 13
ICON 58990 Owner'S Manual & Safety Instructions preview
58990
Brand: ICON Pages: 4
Oldsmobile GM DELTA 88 1974 Owner'S Manual preview
GM DELTA 88 1974
Brand: Oldsmobile Pages: 88
Oldsmobile VISTA-CRUISER 1970 Owner'S Manual preview
VISTA-CRUISER 1970
Brand: Oldsmobile Pages: 67

Brands by name

Popular brands

Load more brands