Lotus 2005 Elise Page 131 Owner'S Handbook Manual Download

Page: 131 / 205

ELECTRICAL

BATTERY

WARNING:

POISON/DANGER - CAUSES SEVERE BURNS KEEP OUT

OF REACH OF CHILDREN.

• Contains sulphuric acid - avoid contact with skin, eyes or

clothing. If in contact with skin or eyes; ﬂush with copious

amounts of water. Remove contaminated clothing. Seek

immediate medical attention. If ingested; seek immediate

medical attention. Do not induce vomiting or give ﬂuids

to drink.

• Batteries produce explosive gases. Keep sparks, ﬂames

and cigarettes away. Ventilate when charging or using in

enclosed space. Always shield eyes when working near

batteries.

RISK OF SHORT CIRCUIT AND FIRE

• Observe all warning notes on the battery.

• Disconnect the battery during all work on the electrical

system.

• Do not lay tools or other metal objects on the battery

as they could cause a short circuit across the battery

terminals.

Battery Access

The ‘maintenance free’ battery is located at the left hand

front of the rear luggage compartment. No routine inspection

or topping up of the electrolyte is required, but at intervals

speciﬁed in the Maintenance Schedule, the battery terminals

should be checked for security and condition, and protected

with petroleum jelly.

For access to the terminals, ﬁrst unclip the battery cover

from the ﬂoor and ease the cover from around the left hand rear

corner of the battery.

Disconnecting the Battery

WARNING:

Failure to follow the correct battery disconnection pro-

cedure detailed below could result in serious burns.

129

oh_croft_InD.indd 129

20/05/2004 07:59:13

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands