Lotus 2005 Elise Page 143 Owner'S Handbook Manual Download

Page: 143 / 205

- To adjust the high beam laterally, adjust the dome headed

screw at the upper inboard side of the lamp, accessed from

behind the lamp. Turn clockwise to adjust the beam to the

right.

- To adjust the vertical aim of the high beam, adjust the dome

headed screw at the lower outboard side of the lamp, ac-

cessed from behind the lamp. Turn clockwise to raise the

beam.

7. Repeat for the RH lamp.

8. Re-ﬁt the cover/mask assemblies complete with edge seal to

the body, and secure with the three socket head screws and

washers. Reﬁt the wheelarch access panel.

m257

Vertical adjuster

Lateral adjuster

High beam lamp

Vertical adjuster

Low beam lamp

141

oh_croft_InD.indd 141

20/05/2004 07:59:16

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands