Lotus 2005 Elise Page 155 Owner'S Handbook Manual Download

Page: 155 / 205

RECOMMENDED LUBRICANTS

Engine

In order to enhance the longevity and reliability of the car, it

is most important that only the speciﬁed lubricants are used. It

is an entirely false economy to try to save money by using lower

quality oils, which may break down before the next change in-

terval and provide inadequate protection before the end of the

term. High oil consumption may also result.

For topping up purposes during the running-in period prior to

the First After Sales Service, a top quality mineral or semi-syn-

thetic 5W/40 oil should be used. At the First After Sales Service

and completion of the running-in period, a fully synthetic 5W/40

oil such as Texaco Havoline Synthetic should be used. This oil

has been tested in all climatic conditions likely to be encountered,

and offers advantages in ease of cranking, smooth cold running

and fuel economy at low temperatures, in combination with good

wear protection at elevated temperatures and at high engine

speeds. If Texaco/Havoline products are not available, an oil

meeting the following speciﬁcation should be used.

NOTICE: Note that Lotus does not recommend the use of any

oil additives and use of such additives may invalidate the terms

of your car’s warranty.

Viscosity:

5W/40

Quality Standard:

API SJEC; ILSAC; ACEA A3

Capacity - reﬁll inc. ﬁlter

4.4 litre

(Cars ﬁtted with front mounted oil coolers contain an additional

3.5 litres, but this oil is not drained during routine servicing)

Difference between high & low dipstick marks

1.5 litre

Oil change interval

Refer to Maintenance Schedule

‘Severe Service’ Conditions

Certain operating conditions can cause rapid degradation of

the oil quality, either by the accumulation of dirt particles, or by

the absorption of water from condensation. If any of the ‘severe

service’ conditions described below apply, it is recommended

that the oil and ﬁlter be changed twice as frequently as is listed

in the Maintenance Schedule.

d L

153

oh_croft_InD.indd 153

20/05/2004 07:59:19

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands