Lotus 2005 Elise Page 85 Owner'S Handbook Manual Download

Page: 85 / 205

4. Roll out the left hand side of the roof, and engage the spigot

pin on the front and rear end of the rail, into the uppermost slot

in the latch blocks at the front and rear of the roof aperture.

5. Ensure that the tensioning cables at the front and rear edges

of the roof canopy are correctly located in the channels be-

tween the seal and body before rotating the left hand side rail

downwards. Ensure that both spring loaded pins ‘click’ into

their ramped slots indicating that latching is complete. Pull

up on the side rail to check security.

6. On the right hand side of the car, repeat steps (4) and (5) for

the second side rail.

NOTICE: Engaging the left hand roof side rail ﬁrst, will minimise

the possibility of the canopy tensioning cable adjusters causing

damage to the roof seals.

WARNING:

Before driving check that the roof is secure by pulling

upwards on each end of both side rails. An inproperly ﬁtted

or insecure roof could cause serious injury or death to car

occupants or other road users.

l O

ohs111

FITTING SIDERAIL

Spigot pin

Spring

loaded pin

oh_croft_InD.indd 83

20/05/2004 07:59:01

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands