Lotus 2005 Elise Page 51 Owner'S Handbook Manual Download

Page: 51 / 205

will also disable the engine coolant pump and result in rapid

overheating; stop the engine as soon as it is safe to do so, and

summon assistance. If the drive belt is intact and the cooling

system unaffected, it may be possible in favourable daylight

conditions, to drive a short distance to a repair facility, but do

not, under any circumstances, allow the battery to become

completely discharged by continuing to drive.

Engine Malfunction Indicator Lamp

The engine Malfunction Indicator Lamp (MIL) is provided to

warn the driver that the engine management system has de-

tected a fault which may result in increased noxious emissions

from the exhaust. In order to minimise emissions and potential

engine damage, various operational limitations may automati-

cally be applied.

i) If the MIL lights continuously whilst driving, immediately reduce

speed and adopt a moderate driving style. Seek dealer advice

without delay and avoid all unnecessary journeys.

ii) If the MIL ﬂashes, an engine misﬁre has been detected which

is likely to cause overheat damage to the catalytic converter.

Slow down immediately and be prepared to stop.

- If the MIL then stops ﬂashing, and is lit continuously, proceed

with caution and seek dealer advice.

- If the MIL continues to ﬂash, stop the car as soon as it is safe

to do so, and switch off the engine. Seek dealer advice.

NOTICE:

Continuing to drive the car with a ﬂashing MIL may

cause overheat damage to the catalytic converter, possible en-

gine damage, increased emissions, and impaired fuel economy

and driveability.

In order to comply with emissions regulations, data regarding

activation of the MIL is recorded in the engine electronic control-

ler, and may be downloaded by Lotus dealers.

Security/RPM Tell Tale

The security tell tale is located at the top of the tachometer

display, and indicates the status of the immobiliser and alarm.

• Tell tale out; engine is mobilised, and the alarm is off.

• Tell tale ﬂashing; engine is immobilised, or alarm is armed

and engine immobilised.

For full details of the car security system, refer to the earlier

section ‘Car Security’.

ts & S

oh_croft_InD.indd 49

20/05/2004 07:58:52

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands