Lotus 2005 Elise Page 142 Owner'S Handbook Manual Download

Page: 142 / 205

3. If adjustment is required, the clear cover and mask must be

removed from the body. From within the wheelarch, remove

the access panel from the wheelarch liner to expose the

headlamp cover retaining screws. Use the hexagonal key

provided in the toolkit (in the rear pocket on the battery

cover) to release the three socket head retaining screws

and washers, and withdraw the cover assembly complete

with rubber edge seal from the body. When reﬁtting, do not

overtighten the ﬁxings.

4. To adjust the low beam laterally, adjust the dome headed

screw at the upper inboard side of the low beam (uppermost)

lamp, accessed from the front of the lamp. Turn clockwise to

adjust the beam to the right. Optimum setting is 0%. To adjust

the vertical aim of the low beam, adjust the dome headed

screw at the lower outboard side of the lamp, accessed

from the front of the lamp. Turn clockwise to raise the beam.

Optimum setting is -1.5%.

5. Repeat for the RH lamp.

6. Centralise the machine on the LH high beam (lowermost)

lamp, and switch on the high beams. Check the high beam

alignment which should be centralised with the marker dot on

the machine screen or slightly below the horizontal. Optimum

setting is 0%.

ohs105a

HEADLAMP COVER UNIT SOCKET BOLTS

140

oh_croft_InD.indd 140

20/05/2004 07:59:16

Summary of Contents for 2005 Elise














































































































































































































Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands

Lotus 2005 Elise, Owner'S Handbook Manual

Search results

Summary of Contents for 2005 Elise

Reviews:

Related manuals for 2005 Elise

Brands by name

Popular brands