Lenovo 7X16 Reference Download Page 93

Page: 93 / 212

Complete the following steps:

1. If the system board or firmware was just updated, check the Lenovo Support site for an applicable

service bulletin or firmware update that applies to this processor error.

2. If problem persists, collect Service Data log.

3. Contact Lenovo Support.

•

FQXSPPU0009N: [ProcessorElementName] has a Configuration Mismatch.

This message is for the use case when an implementation has detected a Processor Configuration
Mismatch has occurred.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - CPU
SNMP Trap ID: 40
CIM Prefix: PLAT CIM ID: 0062

User Action:

Complete the following steps:

1. Check the installed processor spec is the same and matched with supported spec on server proven

plan ( https://static.lenovo.com/us/en/serverproven/index.shtml ) or reseat the processor.

2. If problem persists, collect Service Data log.

3. Contact Lenovo Support.

•

FQXSPPU0011N: An SM BIOS Uncorrectable CPU complex error for [ProcessorElementName] has

asserted.

This message is for the use case when an SM BIOS Uncorrectable CPU complex error has asserted.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - CPU
SNMP Trap ID: 40
CIM Prefix: PLAT CIM ID: 0816

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to

this error.

2. Reboot system.

3. If problem persists, collect Service Data log.

4. Contact Lenovo Support.

•

FQXSPPU2001I: An Over-Temperature Condition has been removed on [ProcessorElementName].

This message is for the use case when an implementation has detected a Over-Temperature Condition
has been Removed for Processor.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Temperature
SNMP Trap ID: 0

Chapter 2

XClarity Controller events

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 93 / 212

Search results

Summary of Contents for 7X16

Reviews: