manualshive.com logo in svg

Lenovo 7X16, Reference, Page: 198 / 212

Share
Download
Lenovo 7X16 Reference Download Page 198

2.  If the problem persists, please contact technical support.

• 

FQXPMUP0003K: Unable to obtain the minimum level of UEFI 

Severity: Warning

User Action:

1.  Restart BMC via supported method and reboot the system.

2.  Reflash BMC firmware.

3.  Perform AC reset or virtual reseat.  

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on 

AC. After AC power is restored, power on the host system.

4.  If the problem persists, please contact technical support.

• 

FQXPMUP0004K: Unable to obtain the installed version of UEFI 

Severity: Warning

User Action:

1.  Restart BMC via supported method and reboot the system.

2.  Reflash BMC firmware.

3.  Perform AC reset or virtual reseat.  

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on 

AC. After AC power is restored, power on the host system.

4.  If the problem persists, please contact technical support.

• 

FQXPMUP0005K: Unable to obtain the installed version of BMC 

Severity: Warning

User Action:

1.  Restart BMC via supported method and reboot the system.

2.  Reflash BMC firmware.

3.  Perform AC reset or virtual reseat.  

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on 

AC. After AC power is restored, power on the host system.

4.  If the problem persists, please contact technical support.

• 

FQXPMUP0006K: Unable to obtain the installed version of LXPM 

Severity: Warning

User Action:

1.  Restart BMC via supported method and reboot the system.

2.  Reflash BMC firmware.

3.  Perform AC reset or virtual reseat.  

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on 

AC. After AC power is restored, power on the host system.

4.  If the problem persists, please contact technical support.

194

ThinkSystem SN550 V2 Messages and Codes Reference

Summary of Contents for 7X16





















































































































































































































Reviews:

No comments