Lenovo 7X16 Reference Download Page 171

Page: 171 / 212

2. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to

this processor error.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU0015K: A processor stepping mismatch has been detected for one or more processors.

Severity: Error

User Action:

Complete the following steps:

1. Verify that matching processors are installed in the correct processor sockets. Correct any mismatch

found.

2. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to

this processor error.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU0016N: A processor within the system has failed the BIST.

Severity: Error

User Action:

Complete the following steps:

1. If the processor or firmware was just updated, check the Lenovo support site for an applicable

service bulletin or firmware update that applies to this processor error.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFPU0017G: A processor microcode update failed.

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

Processor error.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFPU0018N: CATERR(IERR) has asserted on processor [arg1].

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to

this Processor error.

2. Reboot the system.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU0019N: An uncorrectable error has been detected on processor [arg1].

Chapter 3

UEFI events

167

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 171 / 212

Search results

Summary of Contents for 7X16

Reviews: