Lenovo 7X16 Reference Download Page 176

Page: 176 / 212

Information only; no action is required.

•

FQXSFPU4047I: TPM Firmware will be updated from TPM2.0 to TPM1.2.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFPU4049I: TPM Firmware update successful.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFPU4050G: Failed to update TPM Firmware.

Severity: Warning

User Action:

Information only; no action is required.

•

FQXSFPU4051G: Undefined TPM_POLICY found

Severity: Warning

User Action:

Complete the following steps:

1. Reboot the system.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFPU4052G: TPM_POLICY is not locked

Severity: Warning

User Action:

Complete the following steps:

1. Reboot the system.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFPU4053G: System TPM_POLICY does not match the planar.

Severity: Warning

User Action:

Complete the following steps:

1. Remove any newly added TPM card from the planar or re-install the original TPM card that shipped

with the system.

2. Reboot the system.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU4054G: TPM card logical binding has failed.

Severity: Warning

172

ThinkSystem SN550 V2 Messages and Codes Reference

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 176 / 212

Search results

Summary of Contents for 7X16

Reviews: