Lenovo 7X16 Reference Download Page 137

Page: 137 / 212

This message is for the use case where a user has not flashed the firmware component from the interface
and IP address due to a failure.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0036

User Action:

Information only; no action is required.

•

FQXSPUP4003I: [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the

[arg3] firmware.

This message is for the use case where a specific type of firmware mismatch has been detected.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0042

User Action:

Complete the following steps until the problem is solved:

1. AC cycle the system.

2. Reflash XCC/BMC firmware to the latest version.

3. NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

4. If problem persists, collect Service Data log.

5. Contact Lenovo Support.

•

FQXSPUP4004I: XCC firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt

to flash the XCC firmware to the same level on all nodes/servers.

A mismatch of XCC firmware has been detected between nodes/servers

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0132

User Action:

Complete the following steps until the problem is solved:

1. Reflash XCC/BMC firmware to the latest version on all servers.

2. NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

3. If problem persists, collect Service Data log.

Chapter 2

XClarity Controller events

133

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 137 / 212

Search results

Summary of Contents for 7X16

Reviews: