Lenovo 7X16 Reference Download Page 202

Page: 202 / 212

•

FQXPMUP0207M: The update package is invalid. Failed to update the firmware.

Severity: Error

User Action:

1. Ensure the update package is not corrupt and retry the update.

2. Ensure proper connection to USB/network drive and retry the update.

3. Restart BMC via supported method and BMC setting via uEFI setup or "Restart Management

Controller" in BMC web UI. Then, reboot the system.

4. Reflash the BMC firmware.

5. Perform AC reset or virtual reseat.

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on

AC. After AC power is restored, power on the host system.

6. If the problem persists, try a different Lenovo tool to perform the update (eg. XClarity Administrator,

XClarity Controller, or XClarity Essential OneCLI).

7. If the problem persists, please contact technical support.

•

FQXPMUP0208M: Failed to execute reboot BMC command

Severity: Error

User Action:

1. Restart BMC via supported method and reboot the system.

2. Reflash BMC firmware.

3. If the problem persists, perform AC reset or virtual reseat.

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on

AC. After AC power is restored, power on the host system.

4. If the problem persists, please contact technical support.

•

FQXPMVD0001H: Failed to get VPD data.

Severity: Warning

User Action:

1. Press "Back" button and press "Update VPD..." button again.

2. Perform AC reset or virtual reseat if step 1 failed.

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on

AC. After AC power is restored, power on the host system.

3. If the problem persists, please contact technical support.

•

FQXPMVD0002H: Failed to update the VPD data.

Severity: Warning

User Action:

1. Press "Update" button on VPD update page.

2. Perform AC reset or virtual reseat if step 1 failed.

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on

AC. After AC power is restored, power on the host system.

198

ThinkSystem SN550 V2 Messages and Codes Reference

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 202 / 212

Search results

Summary of Contents for 7X16

Reviews: