manualshive.com logo in svg

Lenovo 7X16, Reference, Page: 138 / 212

Share
Download
Lenovo 7X16 Reference Download Page 138

4.  Contact Lenovo Support.

• 

FQXSPUP4005I: FPGA firmware mismatch between nodes/servers [arg1] and [arg2]. Please 

attempt to flash the FPGA firmware to the same level on all nodes/servers. 

A mismatch of FPGA firmware has been detected between nodes/servers

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0133

User Action:

Complete the following steps until the problem is solved:  

1.  Reflash XCC/BMC firmware to the latest version on all servers.

2.  NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device 

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution 
before you update the code.

3.  If problem persists, collect Service Data log.

4.  Contact Lenovo Support.

• 

FQXSPWD0000I: Watchdog Timer expired for [WatchdogElementName]. 

This message is for the use case when an implementation has detected a Watchdog Timer Expired.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 
CIM Prefix: PLAT CIM ID: 0368

User Action:

Information only; no action is required

• 

FQXSPWD0001I: Reboot of system [ComputerSystemElementName] initiated by watchdog 

[WatchdogElementName]. 

This message is for the use case when an implementation has detected a Reboot by a Watchdog 
occurred.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 
CIM Prefix: PLAT CIM ID: 0370

User Action:

Information only; no action is required

• 

FQXSPWD0002I: Powering off system [ComputerSystemElementName] initiated by watchdog 

[WatchdogElementName]. 

134

ThinkSystem SN550 V2 Messages and Codes Reference

Summary of Contents for 7X16





















































































































































































































Reviews:

No comments