manualshive.com logo in svg

Lenovo 7X16, Reference, Page: 153 / 212

Share
Download
Lenovo 7X16 Reference Download Page 153

Note:

It may be necessary to configure slot to Gen1 or to use special utility software so that adapter 

firmware can be upgraded. Gen1/Gen2 settings can be configured via F1 Setup -> System Settings 
-> Devices and I/O Ports ->PCIe Gen1/Gen2/Gen3 Speed Selection, or the OneCLI utility.

4.  If the problem persists, collect Service Data logs.

5.  Contact Lenovo Support.

• 

FQXSFIO0015I: IFM: System reset performed to reset adapters. 

Severity: Info

User Action:

Information only; no action is required. 

• 

FQXSFIO0016M: IFM: Reset loop avoided - Multiple resets not allowed. 

Severity: Warning

User Action:

Complete the following steps:  

1.  Update all firmware (including adapter firmware) to the latest levels.

2.  If problem persists escalate to the next level of support.

• 

FQXSFIO0017M: IFM: Error communicating with the XCC - IFM may not be deployed correctly. 

Severity: Error

User Action:

Complete the following steps:  

1.  Update all system firmware (including adapter firmware) to the latest levels.  

Note:

If the device is part of a cluster solution, verify that the latest level of code is supported for the 

cluster solution before the update.

2.  If the problem persists, collect Service Data logs.

3.  Contact Lenovo Support.

• 

FQXSFIO0018I: IFM: Configuration too large for compatibility mode. 

Severity: Info

User Action:

Information only; no action is required. 

• 

FQXSFIO0019J: PCIe Resource Conflict [arg1]. 

Severity: Error

User Action:

Complete the following steps:  

1.  If this PCIe device and/or any attached cables were recently installed, moved, serviced or upgraded, 

reseat the adapter and any attached cables.

2.  Move the adapter to a different system slot, if available.

3.  Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update 

that applies to this error.  

Chapter 3

.

UEFI events

149

Summary of Contents for 7X16





















































































































































































































Reviews:

No comments