Lenovo 7X16 Reference Download Page 187

Page: 187 / 212

6. Reboot the machine and retry the import of the RAID configuration.

7. If the problem persists, please contact technical support.

•

FQXPMCL0008I: Export uefi settings successfully.

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMCL0008K: Failed to export uefi settings.

Severity: Warning

User Action:

1. Ensure proper connection to USB/network drive and retry to export uEFI setting.

2. Reboot and try the uEFI setting export again.

3. Reflash UEFI firmware.

4. If the problem persists, please contact technical support.

•

FQXPMCL0009I: Import uefi settings successfully.

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMCL0009K: Failed to import uefi settings.

Severity: Warning

User Action:

1. Ensure proper connection to USB/network drive and retry the uEFI setting import.

2. Ensure that same system model type to import the uEFI setting and UEFI version should be the same.

3. Reboot and try to import a new clone of the UEFI settings.

4. Reflash UEFI firmware.

5. If the problem persists, please contact technical support.

•

FQXPMCL0010I: Export bmc settings successfully.

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMCL0010K: Failed to export bmc settings.

Severity: Warning

User Action:

1. Restart BMC via supported method and reboot the system.

2. Perform AC reset.

Note:

When performing AC reset, after powering off AC, wait several seconds before powering on

AC. After AC power is restored, power on the host system.

Chapter 4

XClarity Provisioning Manager events

183

Summary of Contents for 7X16





















































































































































































































Search results

Summary of Contents for 7X16

Reviews:

Lenovo 7X16, Reference, Page: 187 / 212

Search results

Summary of Contents for 7X16

Reviews: