manualshive.com logo in svg

Lenovo 7X16, Reference, Page: 24 / 212

Share
Download
Lenovo 7X16 Reference Download Page 24

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPPW0104J

Non-redundant:Sufficient Resources from Redundancy Degraded or 
Fully Redundant for [RedundancySetElementName] has asserted.

Warning

FQXSPPW0118J

The current chassis configuration is not supported for PMEM 
operation.

Warning

FQXSPPW0119J

Compute node has been gracefully shutdown while CMM is in failsafe 
mode with PMEM ADR complete to prevent data lost.

Warning

FQXSPPW0120J

Unsupported PSU configuration.CPU power has been capped to 
125W.

Warning

FQXSPPW0122J

CMM firmware update required for SN550 V2 support.

Warning

FQXSPSD0002G

Failure Predicted on [StorageVolumeElementName] for array 
[ComputerSystemElementName].

Warning

FQXSPSD0003G

Failure Predicted on drive [arg1] in the enclosure/chassis (MTM-SN: 
[arg2]).

Warning

FQXSPUN0009G

Sensor [SensorElementName] has asserted.

Warning

FQXSPUN0018J

Sensor [SensorElementName] has transitioned from normal to non- 
critical state.

Warning

FQXSPUN0026G

Device [LogicalDeviceElementName] has been added.

Warning

FQXSPBR4003I

Platform Watchdog Timer expired for [arg1].

Error

FQXSPBR4007I

Management Controller [arg1]: Configuration restoration from a file by 
user [arg2] failed to complete.

Error

FQXSPBR4008I

Management Controller [arg1]: Configuration restoration from a file by 
user [arg2] failed to start.

Error

FQXSPCA0002M

Numeric sensor [NumericSensorElementName] going low (lower 
critical) has asserted.

Error

FQXSPCA0009M

Numeric sensor [NumericSensorElementName] going high (upper 
critical) has asserted.

Error

FQXSPCA0011N

Numeric sensor [NumericSensorElementName] going high (upper 
non-recoverable) has asserted.

Error

FQXSPCA0017M

Sensor [SensorElementName] has transitioned to critical from a less 
severe state.

Error

FQXSPCA0019N

Sensor [SensorElementName] has transitioned to non-recoverable 
from a less severe state.

Error

FQXSPCR0001N

Sensor [SensorElementName] has transitioned to non-recoverable 
from a less severe state.

Error

FQXSPEA0002M

Sensor [SensorElementName] has transitioned to critical from a less 
severe state.

Error

FQXSPFW0000N

The System [ComputerSystemElementName] encountered a POST 
Error.

Error

FQXSPFW0001N

Firmware BIOS (ROM) corruption was detected on system 
[ComputerSystemElementName] during POST.

Error

FQXSPFW0002N

The System [ComputerSystemElementName] encountered a firmware 
hang.

Error

20

ThinkSystem SN550 V2 Messages and Codes Reference

Summary of Contents for 7X16





















































































































































































































Reviews:

No comments