Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 811 / 1990

background image

– eXFlash DIMMs

•

806f010d-2b820015 : The [NumericSensorElementName] has been disabled due to a detected fault.

The eXFlash Proxy Service detected a fault on the eXFlash DIMM 21 in Compute Book 2.

May also be shown as 806f010d2b820015 or 0x806f010d2b820015

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Verify that the most recent eXFlash DIMM firmware and eXFlash IPMI Proxy Service are installed.

2. Reinstall your eXFlash IPMI Proxy Service.

3. Perform a full AC power cycle on the system.

4. If the node has recently been installed, moved, serviced, or upgraded, verify that the eXFlash

DIMM is properly seated and visually verify that there is no foreign material in any DIMM
connector on that memory channel. If either of these conditions is found, correct and retry with
the same eXFlash DIMM. (Note: Event Log may contain a recent 00580A4 event denoting
detected change in DIMM population that could be related to this problem.)

5. Check IBM support site for an applicable service bulletin or firmware update that applies to this

eXFlash error.

6. If problem persists and there are no other eXFLash DIMMs with the same indication, confirm that

the eXFlash DIMM is under warranty before replacement.

7. Replace compute book.

8. (Trained Service technician only) Replace affected Processor.

Related links

–  Server features and specifications
–  Removing a compute book
–  Replacing a compute book
–  Removing the compute book cover
–  Replacing the compute book cover
–  Removing a memory module
–  Replacing a memory module
–  eXFlash DIMMs

•

806f010d-2b820016 : The [NumericSensorElementName] has been disabled due to a detected fault.

The eXFlash Proxy Service detected a fault on the eXFlash DIMM 22 in Compute Book 2.

May also be shown as 806f010d2b820016 or 0x806f010d2b820016

Severity

Error

Appendix C. Integrated management module II (IMM2) error messages

797

«
...
809
810
811
812
813
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

Brand: NAIM Pages: 16

Brand: Exsys Pages: 24

Brand: Supermicro Pages: 62

Brand: Synology Pages: 24

TERASTATION HS-D1.0TGL/R5

Brand: Buffalo Pages: 2

Brand: Cisco Pages: 40

IP-DECT SERVER 6500

Brand: SpectraLink Pages: 126

Brand: Thecus Pages: 102

Brand: High End Systems Pages: 224

OfficeConnect 3C19500

Brand: 3Com Pages: 1

Brand: Planex Pages: 134

33610 - 1TB StorCenter Pro NAS 150d Server

Brand: Iomega Pages: 8

Brand: Deep Secure Pages: 12

Brand: Inspur Pages: 205

Brand: Oracle Pages: 6

Exalytics In-Memory Machine

Brand: Oracle Pages: 85

Brand: Inspur Pages: 2

Brand: dallmeier Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands