Lenovo 6241 Installation And Service Manual Download Page 74

Page: 74 / 1990

DIMM 1

DIMM 2

DIMM 3

DIMM 4

DIMM 5

DIMM 6

DIMM 10

DIMM 11 DIMM 12

DIMM 7

DIMM 8

DIMM 9

Microprocessor

The following illustration shows the DIMM connectors on the non-microprocessor side of the compute book
board.

DIMM 24

DIMM 23

DIMM 22

DIMM 19

DIMM 20

DIMM 21

DIMM 15

DIMM 14

DIMM 13

DIMM 18

DIMM 17

DIMM 16

To install a DIMM, complete the following steps.

1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables from the server.

3. Remove the compute book from the server (see “Removing a compute book” on page 291).

4. Remove the compute book cover (left or right cover - depending on the DIMM connector in which you

are installing the DIMM). Press down on both blue touch points on the cover and slide the cover toward
the rear of the expansion module.

Attention:

Remove only one cover (on one side) at a time to protect the compute book components on

the other side of the compute book from being damaged.

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands