Lenovo 6241 Installation And Service Manual Download

Page: 102 / 1990

For information about the supported RAID adapters, see “Supported RAID adapters” on page 86. For
information about the supported Features on Demand software RAID, see “Supported Features on Demand
software” on page 90.

Supported ML2 (Ethernet) adapters

Use this information for an overview of the ML2 (Ethernet) adapters that are supported on the server.

The following table lists the supported Ethernet adapters. For additional information about installing the
adapters, see “Installing an adapter” on page 83 and “Installing an adapter in the standard or half-length I/O
book” on page 90, and “Standard I/O book” on page 31.

Notes:

• You must go to the Lenovo Support web site at

http://datacentersupport.lenovo.com/

and download the

latest device drivers for the ML2 Ethernet adapters. Look for the Ethernet adapters under NIC adapters.
Use the

release notes

and

read.txt

files for the device driver installation instructions.

• Each ML2 (Ethernet) adapter comes with a standard profile bracket and a low-profile bracket. One bracket

might already be installed.

Table 24. Supported ML2 (Ethernet) adapters and where you can install the adapters.

Ethernet adapters

Where to install the
adapter

Notes and Features

Intel X540 ML2 quad-port 1
Gb-T Ethernet Adapter for
System x

This adapter can
only be installed in
slot 10 on the
standard I/O book
board.

• Port 1 on the adapter is the default port for IMM Shared

mode when enabled through UEFI.

• This adapter provides the following features:

– Single chip, quad-port 1 Gb Base-T controller with

integrated MAC and PHY

– PCI Express v2.1 with 5.0 GT/s and 2.5 GT/s support

for x1, x2, and x4 links widths

– Pass-Through (PT) functionality via a sideband interface

– DMTF Network Controller Sideband Interface (NC-SI)

– 1000BASE-T, 100BASE-TX, and 10Base-T link modes

– Flexible port partitioning (32 virtual functions on quad-

port or 16 virtual functions on dual-port)

Intel I350-T4 ML2 dual-port 10
Gb-T Ethernet Adapter for
System x

This adapter can
only be installed in
slot 10 on the
standard I/O book
board.

• Port 1 on the adapter is the default port for IMM Shared

mode when enabled through UEFI.

• This adapter provides the following features:

– Single chip, dual port 10 Gb Base-T controller with

integrated MAC and PHY

– 12.5 watts maximum power

– Unified networking delivering LAN, iSCSI, and FCoE

over 10 Gb Base-T

– Two independent 10 Gb Base-T interfaces with SR-IOV

support

– PCI Express v2.1 with 5.0 GT/s and 2.5 GT/s support

for x1, x2, x4, and x8 links widths

– 10BASE-T, 1000BASE-T, and 100BASE-TX link modes

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands