Lenovo 6241 Installation And Service Manual Download Page 262

Page: 262 / 1990

DIMM 1

DIMM 2

DIMM 3

DIMM 4

DIMM 5

DIMM 6

DIMM 10

DIMM 11 DIMM 12

DIMM 7

DIMM 8

DIMM 9

Microprocessor

The following illustration shows the location of the DIMM connectors on the right side of the compute book
board:

DIMM 24

DIMM 23

DIMM 22

DIMM 19

DIMM 20

DIMM 21

DIMM 15

DIMM 14

DIMM 13

DIMM 18

DIMM 17

DIMM 16

To install a DIMM, complete the following steps:

Step 1. Touch the static-protective package that contains the DIMM to any unpainted metal surface on the

outside of the server. Then, remove the DIMM from the package.

Step 2. Open the retaining clip on each end of the DIMM connector.

Attention:

To avoid breaking the retaining clips or damaging the DIMM connectors, open and

close the clips gently.

248

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands