Lenovo 6241 Installation And Service Manual Download

Page: 266 / 1990

Step 4. Close the PCIe retention lever.

Step 5. Reconnect the cables to the adapter.

Step 6. Reinstall the storage book.

Step 7. Perform any configuration tasks that are required for the adapter.

Step 8. Reconnect the power cord and any cables that you removed.

Step 9. Turn on the peripheral devices and the server.

Removing a USB embedded hypervisor flash device

Use this information for instructions on how to remove a USB hypervisor flash device.

To remove a USB embedded hypervisor flash device, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44 .

Step 2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables as necessary to replace the
device.

Step 3. Remove the standard I/O book from the server (see “Removing the standard I/O book” on page

224).

Step 4. Locate the USB embedded hypervisor flash device connector on the standard I/O book board (see

“Standard I/O book” on page 31 for the location of the connector).

Note:

You can rotate the standard I/O book air baffle up, if needed, to access the USB flash device

connector.

Step 5. Slide the lockbar on the USB flash device connector down to the unlocked position and pull the

USB flash device out of the connector.

252

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands