Lenovo 6241 Installation And Service Manual Download

Page: 483 / 1990

IMM Indicates failure in 9545A bus (BUS 2).

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

166-905-001 : IMM I2C Test Failed

IMM Indicates failure in the 9545A bus (BUS 4).

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

166-908-001 : IMM I2C Test Failed

IMM Indicates failure in the 9545A bus (BUS 7).

Recoverable

Appendix B. DSA diagnostic test results

469

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands