Lenovo 6241 Installation And Service Manual Download

Page: 593 / 1990

CIM Information

Prefix:

PLAT

ID:

0520

User Response

Complete the following steps until the problem is solved:

1. Check the IMM event log for any fan or cooling related issues.

2. Make sure that the airflow at the front and rear of the server is not obstructed and that fillers are

in place and correctly installed.

3. Make sure that the room temperature is within operating specifications.

4. Make sure that all baffles included with the system are installed.

5. Check the heatsink on the ML2 card to ensure that it is free of particulates and dust which would

reduce cooling efficiency.

6. Remove the heatsink on the ML2 card, check to make sure there is good contact between the

heatsink and chip, and then reinstall the heatsink.

•

80070107-0301ffff : Sensor [SensorElementName] has transitioned from normal to non-critical

state.

The Compute Book 1 has been removed from the system. System power blocked.

May also be shown as 800701070301ffff or 0x800701070301ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Alert Category

Warning - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0520

User Response

Install the Compute Book 1 with fans to allow proper cooling to the PCH and FPGA chips.

•

80070107-0302ffff : Sensor [SensorElementName] has transitioned from normal to non-critical

state.

The Compute Book 2 has been removed from the system

May also be shown as 800701070302ffff or 0x800701070302ffff

Appendix C. Integrated management module II (IMM2) error messages

579

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands