Lenovo 6241 Installation And Service Manual Download Page 106

Page: 106 / 1990

Step 2. Follow the cabling instructions, if any come with the adapter. Route the internal adapter cables

before you install the adapter.

Step 3. Remove the full-length I/O book from the server (see “Removing the full-length I/O book” on page

235).

Step 4. Remove the I/O book cover. Slide the cover forward, then lift it off the I/O book.

Step 5. Make sure that the PCIe retention lever is in the open position.

Step 6. Remove the expansion slot cover.

Step 7. Touch the static-protective package that contains the adapter to any unpainted surface on the

outside of the server; then, remove the adapter from the package.

Step 8. Insert the adapter into the connector on the board, aligning the edge connector on the adapter with

the connector on the I/O book board.

Step 9. Press the edge of the connector on the adapter

firmly

into the connector on the board. Make sure

that the adapter snaps into connector securely.

Attention:

When you install an adapter, make sure that the adapter is correctly seated in the

connector on the board before you turn on the server. An incorrectly seated adapter might cause
damage to the board or the adapter.

Expansion
slot cover

Cover

Adapter
(full-length)

Step 10. Connect the auxiliary power cable from the adapter to the board (see the following illustration for

the location of the connector on the board).

Step 11. Close the PCIe retention lever to secure the adapter in place.

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands