Lenovo 6241 Installation And Service Manual Download

Page: 249 / 1990

Release latch

Handle

Filler panel

Step 4. Rotate the handle all the way up and push it into the server until it locks in place.

Step 5. Reconnect any external cables to the adapters, if you removed any earlier.

Step 6. Press the

Power button

on the I/O book to turn the power onto the adapter slots. The Green LED

will begin flashing. When the Green LED stop flashing, the adapter is ready for use.

Removing the full-length I/O book

This information provides instructions for removing the full-length I/O book.

To remove the full-length I/O book, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44 .

Step 2. The full-length I/O book is hot-swappable if no adapters are installed in the I/O book. If adapters

are installed in the I/O book, you must first press the

Power button

on the I/O book and power-off

all three PCIe adapter slots before you remove the I/O book from the server. The slots LED lights
will be off when the slots are off-line.

Step 3. Remove any external cables that are attached to the adapters.

Step 4. Press the blue release latch downward; then, rotate the handle all the way down and slide the I/O

book out of the server.

Chapter 6

Removing and replacing components

235

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands